你不該設置靜態的IP應該設置動態的IP就可以的。因為你是想把有限的網絡變成無線的網絡。把網線插在wan口路由里設置跟你電腦配置一樣的ip地址。就行了。記住了如果你的無線路由進入的ip是192.168.1.1而你的電腦也是這個網段的你還是連接不上的。你需要把你的路由IP改下改成192.168.0.1（這個是我定義的，你也可以自己設置）才行。路由和電腦不能再同一個網段，因為會沖突所以你也上不了網。

步驟如下啊
r1的配置：
router>en
router#en
router#conf t
enter configuration commands, one per line. end with cntl/z.
router(config)#no ip do lo
router(config)#line con 0
router(config-line)#no exec-t
router(config-line)#logg s
router(config-line)#ho r1

r1(config)#ipv6 unicast-routing
r1(config-if)#ipv6 address 2006:bbbb::1/64
r1(config-if)#inter lo1
r1(config-if)#ipv6 address 2007:cccc::1/64
r1(config-if)#inter s2/1
r1(config-if)#ipv6 address 2008:dddd::1/64
r1(config-if)#no shut

*jul 18 20:01:19.879: %link-3-updown: interface serial2/1, changed state to up
*jul 18 20:01:20.887: %lineproto-5-updown: line protocol on interface serial2/1, changed state to up
*jul 18 20:01:48.771: %lineproto-5-updown: line protocol on interface serial2/1, changed state to down
r1(config-if)#exi
*jul 18 20:04:48.771: %lineproto-5-updown: line protocol on interface serial2/1, changed state to up
enter configuration commands, one per line. end with cntl/z.
r1(config)#ipv6 ro...步驟如下啊
r1的配置：
router>en
router#en
router#conf t
enter configuration commands, one per line. end with cntl/z.
router(config)#no ip do lo
router(config)#line con 0
router(config-line)#no exec-t
router(config-line)#logg s
router(config-line)#ho r1

r1(config)#ipv6 unicast-routing
r1(config-if)#ipv6 address 2006:bbbb::1/64
r1(config-if)#inter lo1
r1(config-if)#ipv6 address 2007:cccc::1/64
r1(config-if)#inter s2/1
r1(config-if)#ipv6 address 2008:dddd::1/64
r1(config-if)#no shut

*jul 18 20:01:19.879: %link-3-updown: interface serial2/1, changed state to up
*jul 18 20:01:20.887: %lineproto-5-updown: line protocol on interface serial2/1, changed state to up
*jul 18 20:01:48.771: %lineproto-5-updown: line protocol on interface serial2/1, changed state to down
r1(config-if)#exi
*jul 18 20:04:48.771: %lineproto-5-updown: line protocol on interface serial2/1, changed state to up
enter configuration commands, one per line. end with cntl/z.
r1(config)#ipv6 rout
r1(config)#ipv6 route 2007:aaaa::2/64 s2/1 //靜態路由
r1(config)#end

r1#show ipv6 rou
ipv6 routing table - 9 entries
codes: c - connected, l - local, s - static, r - rip, b - bgp
u - per-user static route
i1 - isis l1, i2 - isis l2, ia - isis interarea, is - isis summary
o - ospf intra, oi - ospf inter, oe1 - ospf ext 1, oe2 - ospf ext 2
on1 - ospf nssa ext 1, on2 - ospf nssa ext 2
c 2006:bbbb::/64 [0/0]
via ::, loopback0
l 2006:bbbb::1/128 [0/0]
via ::, loopback0
s 2007:aaaa::/64 [1/0]
via ::, serial2/1 靜態路由
c 2007:cccc::/64 [0/0]
via ::, loopback1
l 2007:cccc::1/128 [0/0]
via ::, loopback1
c 2008:dddd::/64 [0/0]
via ::, serial2/1
l 2008:dddd::1/128 [0/0]
via ::, serial2/1
l fe80::/10 [0/0]
via ::, null0
l ff00::/8 [0/0]
via ::, null0

r1#ping ipv6 2007:aaaa::2 //通了 哈哈哈哈

type escape sequence to abort.
sending 5, 100-byte icmp echos to 2007:aaaa::2, timeout is 2 seconds:
!!!!!

r2的配置：

router>en
router#conf t
enter configuration commands, one per line. end with cntl/z.
router(config)#no ip do lo
router(config)#line con 0
router(config-line)#no exec-t
router(config-line)#logg s
router(config-line)#ho r2

r2(config-if)#inter lo1

r2(config-if)#ipv6 address 2005:dddd::1/64
r2(config-if)#inter lo0
r2(config-if)#ipv6 address 2007:aaaa::2/64
r2(config-if)#inter s2/1
r2(config-if)#ipv6 address 2008:dddd::2/64
r2(config-if)#no shut
r2(config-if)#exi
r2(config)#ipv6 route ::/0 s2/1 //默認路由
r2#show ipv6 rout
ipv6 routing table - 9 entries
codes: c - connected, l - local, s - static, r - rip, b - bgp
u - per-user static route
i1 - isis l1, i2 - isis l2, ia - isis interarea, is - isis summary
o - ospf intra, oi - ospf inter, oe1 - ospf ext 1, oe2 - ospf ext 2
on1 - ospf nssa ext 1, on2 - ospf nssa ext 2
s ::/0 [1/0]
via ::, serial2/1 默認路由
c 2005:dddd::/64 [0/0]
via ::, loopback1
l 2005:dddd::1/128 [0/0]
via ::, loopback1
c 2007:aaaa::/64 [0/0]
via ::, loopback0
l 2007:aaaa::2/128 [0/0]
via ::, loopback0
c 2008:dddd::/64 [0/0]
via ::, serial2/1
l 2008:dddd::2/128 [0/0]
via ::, serial2/1
l fe80::/10 [0/0]
via ::, null0
l ff00::/8 [0/0]
via ::, null0